Level 2 Inspector Certification Sample Test Survey

Question Title

* 1. You have a piece of wood that measures 2’ long x 2” wide. You need to rip that piece into smaller parts 1⁄2” wide by 2’ long. Knowing that you will lose some of the wood as you cut, how many 1⁄2” strips can you get out of the 2’ x 2” piece?

Question Title

* 2. A 12-foot long class IV pole wood pole can hold a uniform load of 420 pounds per ft.; what total load can the beam support?

4,200 lbs.

4, 060 lbs

5,040 lbs.

5,000 lbs.

Question Title

* 3. The above wood pole (or beam) is used to support a deck at 120lbs per linear foot, plus a railing structure at 45 pounds per linear foot. What total dead load will the beam have to support? Is the beam safe to use to support the deck and railing allowing for the addition of live loads?

2,400 pounds: the beam is safe

1,980 pounds: the beam is safe

4,200 pounds: the beam is not safe

5,300 pounds: the beam is not safe

Question Title

* 4. If the breaking strength of a forged bolt is 10,000 lbs. and we want to proof test the bolt to 20% of the breaking strength, how many US tons of force would need to be applied?

Question Title

* 5. In the question above, what is the estimated minimum factor of safety?

2:1

3:1

5:1

10:1

Question Title

* 6. Which of the following best describes a sectional drawing?

A cutaway view of an object or structure

A drawing as if the object were viewed from above

A drawing of an object as if viewed directly from the front

A drawing of an object if viewed from one side

Question Title

* 7. Site contours are:

Locations of buried utilities

Continuous grade lines that show the height above or below a given reference point

Dimensions that are used to locate a building on a given site

Dimensions that define site boundaries

Question Title

* 8. A perspective drawing (three-dimensional view):

Can be scaled for precise estimation of size

Cannot be scaled

Can be substituted for building elevations

Can be measured and scaled to determine all material sizes

Question Title

* 9. An installation can vary from the ACCT or ASTM standards as long as it has been stamped by a structural engineer and testing to the ASTM standards of those provided by the engineer have been completed and are properly documented

True

False

Question Title

Please use this Image BELOW for Questions 10-13

Question Title

* 10. Identify the bead size of the welds required for proper fabrication

PL3/8

1 /4”

Weld thicknesses are not specified

HSS4x4

Question Title

* 11. Please identify the bolt size specified for attaching the D Plate Anchor Connector:

3/8” x 5”

4” x 4-1/2”

1 /2” A 325

Question Title

* 12. What are the three pipe sizes identified in the above drawing?

10” schedule 40; HSS 4x4x1/2; and 2-1/2” schedule 40

10” schedule 40; PL 3/8”x5; and HSS 4x4x12

2-1/2” schedule 40; 10” schedule 40; and 6” schedule 40

More than three pipe sizes are specified.

Question Title

* 13. For a smaller view of the detail shown above incorporated into the larger structure, you should reference?

A325

Sheet 4

Page 26

The manufactures operations manual

Question Title

Please use this image BELOW for Questions 14- 17

Question Title

* 14. If wheel A turns Clockwise what direction do wheels B and C turn

B is clockwise and C is counterclockwise

B is counterclockwise and C is counterclockwise

B is counterclockwise and C is clockwise

None of the above

Question Title

* 15. If wheel C turns at 40 rotations per minute, approximately how fast will wheel A turn?

60 rotations per minute

80 rotations per minute

20 rotations per minute

40 rotations per minute

Question Title

* 16. Which Gear will have the fewest Rotations Per Minute (RPM)

All turn at the same speed

Question Title

* 17. If an additional gear were installed directly south and below gear C, regardless of its size it would turn

Counter Clockwise

Clockwise

Question Title

Please use this Image for Question 18

Question Title

* 18. To lift the 100 lb. weight illustrated below, you need to pull with a force of about _____ pounds.

100

Question Title

Please use this Image BELOW for Question 19

Question Title

* 19. To lift the 100 lb. weight, you need to pull up with
a force of about _____

100

Question Title

Please use this Image BELOW for Question 20

Question Title

* 20. To lift the 150 lb. weight illustrated above, you need to pull down with a force of about _____ pounds.

100

150

Question Title

Please use this Image BELOW for Question 21

Question Title

* 21. To lift the 200 lb. weight illustrated above, you need to pull down with an approximate force of about _____ pounds.

112

200

Question Title

* 22. Of the choices listed below – The heaviest weight shown that a 1⁄4 Ton Chain Hoist could lift would be?

294 lbs

482 lbs

524 lbs

600 lbs

Question Title

Please use this Image for Questions 23- 25

Question Title

* 23. Assuming all blocks are the same size – please identify how many blocks are touching the block labeled #3

Question Title

* 24. Please identify how many blocks are touching the block labeled #4

Question Title

* 25. Please identify how many blocks are touching the block labeled #5

Question Title

Please use this image BELOW for Question 26

Question Title

* 26. Which lever shown above has the greatest mechanical advantage?

Question Title

Please use this image BELOW for Question 27.

Question Title

* 27. The electrical symbol above is called a?

Coil

Fuse

Switch

Resistor

Question Title

Please use this image BELOW for Question 28.

Question Title

* 28. In the above illustration is the light turned on or off?

Off

Question Title

Please use this Image BELOW for Question 29.

Question Title

* 29. In the circuit shown, how many switches need to be closed to light up at least one bulb?

None

One

Two

Four

Question Title

Please use this Image BELOW for Question 30.

Question Title

* 30. The above illustration from a hydraulic /pneumatic assembly can best be described as?

Check valve

Open Switch

Hydraulic Cylinder

Control Valve

Question Title

Please use this Image BELOW for Question 31.

Question Title

* 31. The illustration above from a hydraulic /pneumatic assembly can best be described as?

Control Valve

Bleeder

Shut off Valve

Check Valve

Question Title

* 32. Which type of Fire Extinguisher should never be used on an oil fire.

Dry Chemical

Water

Carbon Dioxide

None of the Above

Level 2 Inspector Certification Sample Test

Question Title

* 1. You have a piece of wood that measures 2’ long x 2” wide. You need to rip that piece into smaller parts 1⁄2” wide by 2’ long. Knowing that you will lose some of the wood as you cut, how many 1⁄2” strips can you get out of the 2’ x 2” piece?

Question Title

* 2. A 12-foot long class IV pole wood pole can hold a uniform load of 420 pounds per ft.; what total load can the beam support?

Question Title

* 3. The above wood pole (or beam) is used to support a deck at 120lbs per linear foot, plus a railing structure at 45 pounds per linear foot. What total dead load will the beam have to support? Is the beam safe to use to support the deck and railing allowing for the addition of live loads?

Question Title

* 4. If the breaking strength of a forged bolt is 10,000 lbs. and we want to proof test the bolt to 20% of the breaking strength, how many US tons of force would need to be applied?

Question Title

* 5. In the question above, what is the estimated minimum factor of safety?

Question Title

* 6. Which of the following best describes a sectional drawing?

Question Title

* 7. Site contours are:

Question Title

* 8. A perspective drawing (three-dimensional view):

Question Title

* 9. An installation can vary from the ACCT or ASTM standards as long as it has been stamped by a structural engineer and testing to the ASTM standards of those provided by the engineer have been completed and are properly documented

Question Title

Please use this Image BELOW for Questions 10-13

Question Title

* 10. Identify the bead size of the welds required for proper fabrication

Question Title

* 11. Please identify the bolt size specified for attaching the D Plate Anchor Connector:

Question Title

* 12. What are the three pipe sizes identified in the above drawing?

Question Title

* 13. For a smaller view of the detail shown above incorporated into the larger structure, you should reference?

Question Title

Please use this image BELOW for Questions 14- 17

Question Title

* 14. If wheel A turns Clockwise what direction do wheels B and C turn

Question Title

* 15. If wheel C turns at 40 rotations per minute, approximately how fast will wheel A turn?

Question Title

* 16. Which Gear will have the fewest Rotations Per Minute (RPM)

Question Title

* 17. If an additional gear were installed directly south and below gear C, regardless of its size it would turn

Question Title

Please use this Image for Question 18

Question Title

* 18. To lift the 100 lb. weight illustrated below, you need to pull with a force of about _____ pounds.

Question Title

Please use this Image BELOW for Question 19

Question Title

* 19. To lift the 100 lb. weight, you need to pull up witha force of about _____

Question Title

Please use this Image BELOW for Question 20

Question Title

* 20. To lift the 150 lb. weight illustrated above, you need to pull down with a force of about _____ pounds.

Question Title

Please use this Image BELOW for Question 21

Question Title

* 21. To lift the 200 lb. weight illustrated above, you need to pull down with an approximate force of about _____ pounds.

Question Title

* 22. Of the choices listed below – The heaviest weight shown that a 1⁄4 Ton Chain Hoist could lift would be?

Question Title

Please use this Image for Questions 23- 25

Question Title

* 23. Assuming all blocks are the same size – please identify how many blocks are touching the block labeled #3

Question Title

* 24. Please identify how many blocks are touching the block labeled #4

Question Title

* 25. Please identify how many blocks are touching the block labeled #5

Question Title

Please use this image BELOW for Question 26

Question Title

* 26. Which lever shown above has the greatest mechanical advantage?

Question Title

Please use this image BELOW for Question 27.

Question Title

* 27. The electrical symbol above is called a?

Question Title

Please use this image BELOW for Question 28.

Question Title

* 28. In the above illustration is the light turned on or off?

Question Title

Please use this Image BELOW for Question 29.

Question Title

* 19. To lift the 100 lb. weight, you need to pull up with
a force of about _____